0531-83510047
19863682868

大家都在搜: 食品级输送带 新葡萄京娱乐场网址 切菜机输送带

当前位置: 新葡萄京 - 资讯中心 > 行业百科 > 行业百科

挡边输送带会出现撒料情况的原因!

来源: 时间:2020-04-20 11:32:16 浏览次数:
  当输送带跑偏时,是由于输送带的两个边高在运行过程中发生了变化。当另一侧较低时,物料从较低一侧分散,处置方法是调整输送带偏差。在凹面段曲率半径较小的情况下,为什么输送带处于悬浮状态?以下是某输送带厂家技术人员为您先容
  When the conveyor belt deviates, it is because the two side heights of the conveyor belt have changed during the operation. When the other side is lower, the material is dispersed from the lower side, and the disposal method is to adjust the conveyor belt deviation. In the case of small curvature radius of concave section, why is the conveyor belt in suspension? Here is an introduction to the technician of a conveyor belt manufacturer
  1. 在购买输送带时,应准确说明具体物料的名称和性质。特别是,粒度、温度,可有酸、碱等腐蚀性和特殊要求。详细说明了具体的应用场合,对宽度、长度、层数、厚度的要求,特别是耐热输送带的温度和体积。在传送带的运输和储存温度之间应该保持18-40℃,相对湿度应保持在50 - 80%之间,坚持清洁,以防止阳光直射或雨雪,避免接触酸、碱、油、有机溶剂和其他物质,远离加热装置米
  1. When purchasing the conveyor belt, the name and nature of specific materials shall be accurately stated. In particular, the particle size, temperature, acid, alkali and other corrosive and special requirements. The requirements for width, length, number of layers and thickness, especially the temperature and volume of heat-resistant conveyor belt, are described in detail. Keep 18-40 ℃ and 50-80% relative humidity between the transportation and storage temperature of conveyor belt, keep clean to prevent direct sunlight or rain and snow, avoid contact with acid, alkali, oil, organic solvent and other substances, and keep away from the heating device
  2. 在输送带储存期间,产品应成卷存放,不得折叠。传送带每季度应翻转一次。输送带表面清洗:首先将检针器的灵敏度调整到水平。如验针机为B/C模式,请将验针机调至C模式,以免影响下一步的清洁工作。然后将毛巾拉直,在传送带表面适当压紧,启动机器,使机器运行5次以上,将毛巾洗净并拧干,重复此步骤,直到传送带表面没有明显的污染物;干净的传送带:干净,拧了毛巾,毛巾穿过传送带的底部从机器的底部,伸直毛巾,并绘制毛巾输送机表的前面,抓住毛巾两端,启动机器操作数周,随着传送带的底部是更脏的地方,需要多次擦拭\
新葡萄京娱乐场网址
  2. During the storage of conveyor belt, the products shall be stored in rolls and shall not be folded. The conveyor belt should be flipped quarterly. Belt surface cleaning: first adjust the sensitivity of needle detector to the lowest level. If the needle testing machine is in B / C mode, please adjust the needle testing machine to C mode to avoid affecting the next cleaning work. Then straighten the towel, properly press it on the surface of the conveyor belt, start the machine, run the machine for more than 5 times, wash and wring the towel, repeat this step until there is no obvious pollutant on the surface of the conveyor belt; clean conveyor belt: clean, wring the towel, the towel passes through the bottom of the conveyor belt, straighten the towel from the bottom of the machine, draw the front of the towel conveyor table, and grasp both ends of the towel, Start the machine for several weeks, as the bottom of the conveyor belt is the dirtiest place, it needs to be wiped several times
  3、检针机传送带上面的两个清洁步骤之后,灵敏度调整到8级或灵敏度,启动机器,机器的操作,如机器平稳运行和金属探测器位置指示灯不亮,没有金属杂质的衣服,衣服可以顺利通过检针机、传送带清洗成功!如果开机后仍然发现探头灯持续闪烁,衣服不能顺利通过,可能是你没有清洗干净,需要重新清洗。注意:清洗试验后,需要避免周围环境因素的干扰
  3. After the two cleaning steps on the conveyor belt of the needle detector, adjust the sensitivity to level 8 or maximum sensitivity, start the machine, and operate the machine, such as the smooth operation of the machine, the position indicator light of the metal detector is not on, and the clothes without metal impurities, The clothes can pass the needle detector and the conveyor belt successfully. If the probe light continues to flash after the machine is turned on, the clothes can't pass smoothly. Maybe you haven't cleaned them and need to be cleaned again. Note: after the cleaning test, it is necessary to avoid the interference of surrounding environmental factors
  通过输送带厂家的技术人员来先容一下侧输送带发芽的原因你学到了吗?希翼大家的先容能对你有帮助。
  Through the technical personnel of the conveyor manufacturer to introduce the reasons for the germination of the lower conveyor belt, have you learned? I hope our introduction can help you.

产品中心 PRODUCT CENTER

联系大家CONTACT US

手机:13791000079(孙经理)
座机:0531-83510047
QQ(客服):136559297
地址:山东省济南市章丘区刁镇民营经济开发区

XML 地图 | Sitemap 地图