0531-83510047
13964193999

大家都在搜: 食品级输送带 新葡萄京娱乐场网址 切菜机输送带

当前位置: 新葡萄京 - 资讯中心 > 常见问题 > 常见问题

新葡萄京娱乐场网址如何进行吊装呢?

来源: 时间:2020-06-12 16:25:17 浏览次数:
  提升大角度传送带时,应选择一个合理的方法,禁止大角度传送带直接用钢丝绳吊装,由于较重的重量大角传送带,直接提升传送带,传送带将造成严重的损失,提升新葡萄京娱乐场网址制造商纠正方法是胶带钢丝绳,吊装与圆辊(200毫米长度大于带宽)。吊装步骤为:
  When lifting the large angle conveyor belt, a reasonable method shall be selected. It is forbidden to directly lift the large angle conveyor belt with steel wire rope. Because of the heavy weight of the large angle conveyor belt, lifting the conveyor belt directly will cause serious losses. The correction method of lifting the large angle conveyor belt manufacturer is belt steel wire rope, lifting and roller (the length of 200 mm is greater than the belt width). The hoisting steps are as follows:
  1.将滚轮放在翼带底部
  1. Place the roller on the bottom of the wing belt
新葡萄京娱乐场网址
  2.输送带厂家先容,输送带由钢丝绳穿过输送带辊,将输送带辊挂在吊钩上,保证了输送带提升时的平均速度和运行平稳。
  2. The conveyor belt manufacturer introduces that the conveyor belt passes through the center of the conveyor belt roller by the steel wire rope, and the conveyor belt roller is hung on the hook to ensure the average speed and smooth operation of the conveyor belt when it is lifted.
  3.调整托辊两侧宽部及钢丝绳,使倾角大的输送带两侧保持稳定,防止输送带在吊装过程中出现吊装偏差。
  3. Adjust the width of both sides of the idler and the steel wire rope to keep both sides of the conveyor belt with large inclination angle stable and prevent the conveyor belt from hoisting deviation in the hoisting process.
  4.铁架吊装、输送、装载时,吊装前应测量铁架长度,以保证高倾角输送带一次到位。当从铁架内部卸车或取下边缘时,应按上述方法操作。
  4. During the hoisting, transportation and loading of the iron frame, the length of the iron frame shall be measured before hoisting to ensure that the high angle conveyor belt is in place once. When unloading or removing the edge from the inside of the iron frame, the above methods shall be followed.
  新葡萄京娱乐场网址建议在吊装高倾角输送带时,应注意什么?滚筒的直径应符合要求,以免在折边处受力过大而损坏皮带。严禁皮带使用钢丝绳吊装损坏,否则会导致皮带断裂。输送带厂家建议,提升倾角大的输送带时,应增加一个保护辊。使用同一规格型号的输送带时,要求两个托辊受力,防止钢丝绳受力过大对人员和设备造成伤害。
  What should be paid attention to when lifting the high angle conveyor belt? The diameter of the drum should meet the requirements, so as to avoid damage to the belt due to excessive stress at the hem. It is strictly prohibited to use steel wire rope to lift the belt for damage, otherwise the belt will be broken. The conveyor belt manufacturer suggests that when lifting the conveyor belt with large inclination angle, a protective roller should be added. When the conveyor belt of the same specification and model is used, two idlers are required to be stressed to prevent damage to personnel and equipment caused by too much stress on the steel wire rope.

产品中心 PRODUCT CENTER

联系大家CONTACT US

手机:13964193999(孙经理)
座机:0531-83510047
QQ(客服):136559297
地址:山东省济南市章丘区刁镇民营经济开发区

XML 地图 | Sitemap 地图